1、確定待包裝產品的尺寸
1. Determine the size of the product to be packed
產品的尺寸直接決定外包裝箱的大小，其準確度非常重要。用卷尺將產品的長、寬、高精確地測量出來，并記錄到紙上，對于外形不規則的物品，一定要選取大點進行測量。如果需要用到輔助包材，要將輔助包材的尺寸也計算到產品尺寸里面。
The size of the product directly determines the size of the outer packing box, and its accuracy is very important. Measure the length, width and height of the product accurately with a tape measure, and record it on the paper. For objects with irregular shape, large points must be selected for measurement. If auxiliary packaging material is needed, the size of auxiliary packaging material shall be calculated into the product size.
2、確定紙板的尺寸
2. Determine the size of the cardboard
要根據產品的尺寸來確認用來做紙箱的紙板的大小。需要注意的是，如果紙箱完全按照產品的尺寸來定長、寬、高，在由紙板折為紙箱時，紙板往里收，會占去一些紙箱的可用空間，會導致包裝偏緊或無法包下產品。因此我們需要將產品的長寬高適當放大一些來保證紙箱的內部空間足夠包下產品。
According to the size of the product to confirm the size of the cardboard used to make cartons. It should be noted that if the length, width and height of the cartons are completely determined according to the size of the products, when the cardboard is folded into a carton, the cardboard will be collected inward, which will take up the available space of some cartons, resulting in tight packing or inability to pack the products. Therefore, we need to enlarge the length, width and height of the product to ensure that the internal space of the carton is enough to cover the product.
3、裁切紙板
3. Cutting board
將準備好的紙板平鋪在地板上，用卷尺量出需要的長度，并用筆劃出記號，注意一定要選取兩個點，因?yàn)閮牲c(diǎn)才成直線。標記好兩個點后，移去卷尺，用直尺或者其它直的工具沿著兩個點的方向壓住紙板，美工刀沿著直尺往下劃割紙板，注意刀身不要伸出太多，刀刃與紙板間的角度不要太大，用刀刃平順地沿直尺一劃到，力稍大一些，盡量一次性將紙板劃斷。
Lay the prepared paperboard on the floor, measure the required length with a tape measure, and mark with a pen. Pay attention to select two points, because the two points form a straight line. After marking the two points, remove the tape measure, press the cardboard with a straight edge or other straight tools along the direction of the two points, and cut the paperboard with an art knife along the straight edge. Pay attention not to extend the blade too much, and the angle between the blade and the cardboard is not too large. Use the blade to make a smooth cut along the ruler with a little more force. Cut the cardboard at one time as much as possible.
4、制作紙箱壓線
4. Making carton line
紙板裁切好后，要做的就是將我們記錄在紙上的尺寸標到紙板上來。根據記錄的尺寸，用卷尺在紙板上量出相應的尺寸，并用筆劃出記號，效果圖如下：標好記號后，接下來就要?jiǎng)潐壕€。用直尺將紙板兩邊相對應的兩個點比齊，使其在同一條直線上，用美工刀沿直尺輕劃紙板，劃的過程中直尺要壓緊，不要讓其移動，以免劃的不直；注意用力要輕，只需用刀尖將紙板表皮劃破，看到痕跡即可，千萬不要?jiǎng)澋奶钜悦鈱⒓埌鍎潝唷?/div>
After the paperboard is cut, what we need to do is to mark the size we recorded on the paper to the cardboard. According to the recorded size, measure the corresponding size on the cardboard with a tape measure, and mark with a pen. The effect picture is as follows: after the mark is marked, the next step is to mark the line. Use a ruler to align the two corresponding points on both sides of the paperboard to make them in the same straight line. Use an art knife to gently scratch the cardboard along the ruler. During the process of scribing, the ruler should be pressed tightly, and it should not be moved so that it will not be scratched straightly. Pay attention to the light force, just use the knife tip to cut the surface of the paperboard and see the trace. Don't scratch too deep to avoid cutting the cardboard.
5、紙箱成型
5. Carton forming
將紙板沿長邊按劃好的壓線折起來，形成一個長方體，接合部分放在紙箱里邊，如果有白膠，可以在接合部分涂一些白膠，或者用強力雙面膠也行，將接合部分粘貼起來，然后再在外側用透明膠帶封好。將任意一端的開口部分折合起來，同樣用透明膠帶封好。此，普通箱的制作基本完成了。
Fold the paperboard along the long side according to the marked pressure line to form a cuboid. The joint part is placed inside the carton. If there is white glue, you can apply some white glue to the joint part, or use strong double-sided adhesive tape. Paste the joint part, and then seal it with transparent tape on the outside. Fold up the opening at any end and seal it with transparent tape. So far, the production of the ordinary box is basically completed.
今天小編給大家介紹的是
紙箱廠家的相關知識，更多的精彩內容請點擊我們的網站咨詢：
http://flyconn.cn我們后續會有更多的知識為您奉上。
Today, I'd like to introduce you the knowledge of carton manufacturers. For more details, please click our website: http://flyconn.cn We will have more knowledge for you.
