一、印刷是否完整、清晰。
1、 Whether the printing is complete and clear.
所謂“人靠衣裝馬靠鞍”嘛，所以，產品的外包裝是否清晰完整，也會影響消費者對產品的看法。所以合格的紙箱，應該要做到：紙箱包裝箱體印刷圖案，文字明晰正確，印刷墨跡沒有掉墨現象，無錯字、錯印、漏印、重印多余的印刷圖案及字跡，條碼可辨認。
The so-called "people rely on clothes and horses rely on saddles". Therefore, whether the outer packaging of products is clear and complete will also affect consumers' views on products. Therefore, qualified cartons should achieve: the printed patterns of carton packaging box should be clear and correct, the printing ink should not drop, there should be no wrong words, wrong printing, missing printing, reprinting of redundant printed patterns and handwriting, and the bar code can be recognized.
二、箱體是否干凈。
2、 Whether the box is clean.
我們試想一下，同樣的兩個產品放在箱子里，可有一個箱子上面銹跡斑斑，你還會選擇它嗎？所以，我們要做到紙箱箱體外表不允許有任何損壞和污跡，無銹斑、剝層、龜裂和其它紙材缺陷，紙箱包裝箱體里紙面紙不允許有拼接、缺材、露楞、折皺、透膠、色差等感官缺陷，預印和膠印UV包裝箱面紙上UV層允許有細微裂痕，不允許有掉渣現象。
Let's imagine that the same two products are put in a box, but one box is rusty. Will you still choose it? Therefore, we should ensure that the appearance of the carton box is free of any damage and stain, rust, peeling, cracking and other paper defects, the paper surface in the carton packaging box is free of sensory defects such as splicing, lack of material, exposed ridge, wrinkle, glue penetration and color difference, and the UV layer on the surface paper of the pre printed and offset UV packaging box is free of fine cracks and slag dropping.
三、壓痕線是否完整。
3、 Whether the indentation line is complete.
紙箱箱體壓痕線寬度不得大于12mm，折線居中，不得有裂破、斷線、重線等多余的壓痕線及影響感官折跡缺陷。
The width of the indentation line of the carton box shall not be greater than 12mm, the folding line shall be in the middle, and there shall be no excess indentation lines such as crack, broken line and heavy line and folding defects affecting the senses.
四、粘合是否平均、結實。
4、 Whether the bonding is even and firm.
紙箱包裝箱體粘合劑為玉米淀粉膠，膠液應涂布平均，充沛，無溢出。粘合必須劃一、結實、兩片接頭對齊，上下左右錯位不得大于2mm，無箱體與箱體互貼等現象。
The adhesive of carton packaging box is corn starch glue, and the glue liquid shall be coated evenly, abundant and free of overflow. The bonding must be uniform and firm, and the two joints shall be aligned. The dislocation of up, down, left and right shall not be greater than 2mm, and there is no mutual adhesion between the box and the box.
Today, Xiaobian presents you the relevant knowledge about heavy corrugated box manufacturers. If you have any questions and questions about this article, please call us or leave a message at the bottom of the website: http://flyconn.cn
